Plumbing jobs run straight into the most heavily regulated hazard in a building: gas. In homes and in workplaces such as shops, restaurants, schools and hospitals, work on gas fittings must be carried out by a Gas Safe registered engineer who is qualified for that work, and HSE states plainly that it is illegal for anyone else to do it. A plumbing risk assessment therefore has to draw the line around gas work first, then cover soldering, stored water, older building materials, tight spaces and heavy lifting.
Based on HSE — Gas safety for employers, read 2026-10-19. This page is a starting point you must adapt to your own site, people, equipment and the client's rules. It is not a substitute for an assessment by a competent person.
Hazards and controls
| Hazard | Who is at risk | Controls |
|---|---|---|
| Work on gas fittings by someone not registered | Occupants, plumbers, public | In domestic properties and workplaces such as shops, restaurants, schools and hospitals, work on gas fittings only by a Gas Safe registered engineer qualified for that type of work — their Gas Safe ID card checked; in factories, construction site huts and similar premises, only by a competent person. |
| Gas leaks, fire and explosion | Occupants, plumbers | If a leak is suspected: supply turned off, the gas emergency service or LPG supplier called, the building evacuated if in doubt; supply not turned back on until a competent person has dealt with the leak. |
| Carbon monoxide from appliances and blocked flues | Occupants | Air inlets not blocked and flues and chimneys not obstructed by the plumbing work; any appliance known or suspected to be unsafe not used and reported. |
| Burns and fire from soldering and brazing | Plumbers, occupants | Combustibles moved or shielded with a heat mat; extinguisher to hand; area checked after work; push-fit or press-fit fittings where hot work can be avoided. |
| Legionella in stored and stagnant water | Plumbers, occupants | Spray from dead legs, tanks and showers minimised during work; systems flushed and left so water does not stagnate; the building's water risk assessment followed where there is one. |
| Asbestos in older buildings (bath panels, boxing, lagging, flue pipes) | Plumbers, occupants | Asbestos register checked before disturbing materials in older buildings; anything suspect left alone until it has been identified. |
| Lofts, under-floor voids and other tight spaces | Plumbers | Boards laid across joists; lighting; whether the space is a confined space assessed before entry; someone aware of where you are working. |
| Manual handling of cylinders, radiators and baths | Plumbers, labourers | Two-person lifts or trolleys for heavy items; route cleared before carrying; loads drained before moving. |
Method statement — sequence of work
- Scope checked: any work on gas fittings identified and passed to a Gas Safe registered engineer qualified for it; the plumbing work planned around it.
- Asbestos register and building information checked; water supply isolated and drained; stagnant sections flushed with spray kept down.
- Hot work area prepared with heat mat and extinguisher, or a cold-joint method chosen; voids and lofts boarded and lit.
- System refilled and checked for leaks; flues and ventilation left unobstructed; area checked for smouldering before leaving.
What to include in the written assessment
- Site address, the task, the date and who carried out the assessment.
- Each hazard above with the people at risk, the controls in place and the residual risk rating.
- The equipment, PPE and competence (training, cards) the controls depend on.
- Emergency and rescue arrangements, first aid and the nearest A&E.
- A review date and a signature line for the person in charge and the operatives who have read it.
Many plumbers hand their year-end figures to a professional, and a breakdown of what an accountant typically costs shows what affects the fee.
Get the document
Download the free risk assessment template (Word) and fill in the table above for your job, or have the RAMS generator produce a completed risk assessment and method statement for this trade in Word for £19.
Questions
Can a plumber who is not Gas Safe registered connect a gas cooker or boiler?
No. HSE states that in homes and workplaces such as shops, restaurants, schools and hospitals, work on gas fittings must be done by a Gas Safe registered engineer qualified for that work, and it is illegal for anyone else to do it.
How can a customer check someone is Gas Safe registered?
HSE says registration and qualifications can be checked on the Gas Safe Register website or by phone, and registered engineers carry a Gas Safe ID card showing the type of work they are qualified to do.
Need the finished document, not just the guide?
Answer a few questions about the job and get a completed RAMS in Word, ready to send — £19 including VAT, supplied straight after payment.
Build my RAMS — £19Also as editable Word files, £9 each: Method statement template · Health and safety policy template.